Filters

Fiber Optic Fusion Splicingm, Fitel KIT: S153A V2 + S326 Cleaver

Fusion Splicer S153A

Active V-groove is more reliable than conventional Fixed V-groove splicer
Rugged and compact hand-held design to endure any kind of environmental conditions
Internal battery charging
Fast splice (9sec) at super low loss and fast heating(25sec)
200 cycles (Splicing & heating) with two batteries
Available for All METRO/LAN/FTTx fibers including ultra bend-insensitive fibers(G657)
Easily exchanged fiber holder systems
Applicable for Splice-On-Connector(SOC)
Cooling Tray CTX-01
Car Charger CDC-01

Brand:Fitel Fusion Splicers

Price excl. VAT:€0.00 + VAT

Price inc. VAT:€0.00

Alignment Type:	Active V-Groove (Clad Alignment)
Fiber Count:	Single Fiber
Cladding Diameter:	80 to 150 μm
Coating Diameter:	Single: 100 - 1000 μm
Fusion time:	9-11 seconds

Can be ordered by Email

Code: MT00718

Request This Product	Rate this product
Add to wishlist	Compare

The S153A Active 3 Axis Cladding Alignment Fusion Splicer has been enhanced and updated to version 2. The battery is automatically charged internally when connected to AC mains power even during operation. The new illumination lamp lights up a wide area around the V-grooves and helps operation in low light environment. The redesigned and strengthened heater simplifies the protection sleeve loading process.

Features and applications

S153A is the first choice for low cost field splicing equipment. The Active V-Groove technology used on the S153A delivers low loss splices with ease while eliminating common Fixed V-Groove splicing errors.
Using the rugged metal body, the S153A is designed to endure harsh operating conditions by improving shock/impact resistance with rubber pads embedded on 4 corners of the splicer body. It also achieves water resistance compliant to IPX2 and dust resistance compliant to IP5X. Another key feature of the S153A is the significantly reduced operation time. Protection sleeve shrink time is mere 25 seconds, while splicing requires only 9 seconds. Power saving technology used in these machines allows up to 200 splicing cycles (splicing and heating) with 2 built in rechargeable batteries.
By combining ease of use, improved speed, precision, durability and portability, the S153A Fusion Splicer becomes your first choice for a versatile low cost splicer with a wide range of applications.

How is Fiber Optic Splicing done?

Fusion splicing is using localized heat to melt or fuse the ends of two optical fibers and connect them with each other. The splicing begins by getting each fiber end ready to be fused.

Fiber Stripping before Splicing

The protective coating made of polymer surrounding the optical fiber has to be removed in order for it to be ready for fusion splicing. When both fiber ends for fusion are ready the splicing can be started, each fiber should first lose its protective coating. Using a fiber stripper, all that can be done easily.

Fiber ends cleaning

Any dust or particles on the end of the optic fiber can affect the light signal or even block it. After the two ends are fused together through the splicing process, no dust or anything, not even air, should be inside the linking point.

Fiber optic Cleaving

Cleaving means cutting the edges of the fiber ends in order to ensure that each in 90° degree to fiber; when the two end meet they should be perfectly flat and touching each other completely.

Actual Fiber Splicing Step

Just put the two fiber ends into the splicer and start the fusion when they are in complete contact, then the machine runs a test to ensure the splice will survive long time usage and that the light loss at the splice is at minimum. The best result should be 00.00 dB, which means the splicing was perfect.

Alignment Type:	Active V-Groove (Clad Alignment)
Applicable Fiber:	SM / MM / DSF / NZD / BIF / UBIF
Fiber Count:	Single Fiber
Cladding Diameter:	80 to 150 μm
Coating Diameter:	Single: 100 - 1000 μm
Fusion time:	9-11 seconds
Cleave Length:	5-10 or 5-16 mm - 250 μm Coating 10-16 mm - 900 μm Coating

	V-Groove Cleaning Brush V-Groove Cleaning Brush V-Groove Cleaning Brush, suits ribbon and single fiber cladding alignment vee groove blocks. Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	Electrode Sharpener Fitel electrode sharpener, cleans and maintains the precise tip for quality splicing, typical Fitel electrode life is 5000 splices with a clean every 1000 with this sharpener. Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	Spare Electrodes for S178 Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	S178/153 Hard Carrying Case S178/153 Hard Carrying Case Hard Carrying Case, rugged construction with foam cutouts to suit the splicer and accessories. Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	Tool Case Tool Case for S178A V2 Fusion Splicer Accesories Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	2 × S943 Battery for S178/153/123 Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock
	AC Adaptor for S178 AC Adaptor for S178 Price excl. VAT:€0.00 Price inc. VAT:€0.00 Out of stock

File	Info
S153A_FITEL_FUSION_SPLICER_Datasheet	[PDF, 2.37 MB]
S326_FITEL_Datasheet	[PDF, 581.11 KB]

Telecommunications

Heating Syetems

Energy

Leak Detection Systems

Corrosion Prevention