USD
  • TRY
  • USD
  • EUR
  • GBP
+90 444 1 726
Filters

samm market link 1

Calculating Fiber Loss and Distance Estimates

Calculating Fiber Loss and Distance Estimates

Calculating Fiber Loss and Distance Estimates

Fiber Loss Online Calculator

 
 
Fiber Loss = 0.00 dB
0.00 dB *
 
 
 

*The main result is the actual safe value and the second result is the theoretical best value on a new line in perfect conditions.

 

This fiber loss calculator can estimate the total fiber link loss through a particular fiber optic link if the fiber length, the number of splices and number of connectors are known. This calculation is simply the sum of all worst-case loss variables in the link.

 

Fiber Loss Manual Calculation

 

There are a number of ways to tackle the problem of determining the power requirements for a particular fiber optic link. The easiest and most accurate way is to perform an Optical Time Domain Relectometer (OTDR) trace of the actual link.

This will give you the actual loss values for all events (connectors, splices and fiber loss) in the link. In the absence of an actual OTDR trace, there are two alternatives that can be used to estimate the power requierements of the link. 

 

  1. Estimate the total link loss across an existing fiber optic link in the fiber length and loss variables are known
  2. Estimate the maximum fiber distance if optical budget and loss variable are known.

 

Loss variables are connectors, splices and attenuation per kilometer of the fiber. If actual values for all of the loss variables are not known, an estimation for each is needed to complete the calculations. In this case, one would want to take a worst case approach to assure that there is adequate power available for the link. The following table includes commonly accepted loss values in these calculations:

 

 
Fiber Type Wavelength Fiber attenuation / km* Fiber attenuation / km # Connector Loss Splice Loss
Multimode 50/150µm 850 nm 1300 nm 3.5 dB 1.5 dB 2.5 dB 0.8 dB 0.75 dB 0.75 dB 0.1 dB
Multimode 52.5/125µm 850 nm 1300 nm 3.5 dB 1.5 dB 3.0 dB 0.7 dB 0.75 dB 0.75 dB 0.1 dB
Single Mode 9µm 1310 nm 0.4 dB 0.35 dB 0.75 dB 0.1 dB
Single Mode 9µm 1550 nm 0.3 dB 0.22 dB 0.75 dB 0.1 dB
 

* These values are per TIA/EIA and other industry especifications and are the values used by Transition Networks in all link loss calculations.

# These values are one example of the performance that can be obtained with a new fiber installation.

 

The IEEE also recommends maximum cable distances as defined in the table below: 

 

 
Standard Data-Rate (Mbps) Cable Type IEE Standard-Distance
10BASE-FL 10 850nm-Multimode 50/125µm 62.5/125µm 2km.
100BASE-FX 100 1300nm-Multimode 50/125µm 62.5/125µm 2km.
100BASE-SX 100 850nm-Multimode 50/125µm 62.5/125µm 300m.
1000BASE-SX 1000 850nm Multimode 50/125µm  
850nm Multimode 62.5/125µm
550m.
220m.
1000BASE-LX 1000 1300nm Multimode 50/125µm 62.5/125µm 1310nm Single Mode 9/125µm 5km.
1000BASE-LH 1000 1550nm Single Mode 9/125µm 70km.



 

Estimate Total Link Loss

 

This calculation will estimate the total link loss through a particular fiber optic link where the fiber length, as well as the number of splices and connectors, are known. This calculation is simply the sum of all worst-case loss variables in the link:

 

Link Loss = [fiber length (km) × fiber attenuation per km] + 
                   [splice loss × # of splices]
                   [connector loss × # of connectors] + [safety margin]

 

For example: Assume a 40 km. single mode link at 1310nm with 2 connector pairs and 5 splices.

Link loss = [40km × 0.4dB/km] + [0.1dB × 5] + [0.75dB × 2] + [3.0dB] = 21.0dB

 

In this example, an estimated 21.0dB of power would be required to transmit across this link. Of course, it is very important to measure and verify the actual link loss values once the link is established to identify any potential performance issues. (Please check our OTDR Test Measurement Devices category).

 

 

OTDR Measurement Devices

   

Estimate Fiber Distance

 

This calculation will stimate the maximum distance of a particular fiber optic link given the optical budget and the number of connectors and splices contained in the link:

 

Fiber length = ([Optical budget] - [link loss]) / [fiber loss/km]

Fiber length = {[(min. TX PWR) - (RX sensitivity)]
                       - [splice loss × # of splices]
                       - [connector loss × # of connectors]
                       - [safety margin]
                       ÷ [fiber lost/km]

 

For example: Assume a Fast Ethernet Single mode link at 1310nm with 2 connector pairs and 5 splices:

 

Fiber length = {[(-8.0dB) - (-34.0dB)] - [0.1dB × 5] - [0.75dB × 2] - [3.0dB]} / [0.4dB/km] = 52.5km.

 

In this example, an estimated 52.5 km. distance is possible before dissipating the optical power to a value below the Rx sensitivity. As always, it is very important to measure and verify the actual link loss values once the link is established to identify potential performance issues. Actual maximum distances will be very depending on: 

  • Actual optical fiber attenuation per km
  • Optical fiber design and age
  • Quality of connectors and actual loss per pair
  • Quality of splices and actual loss per splice
  • Quantity of splices and connectors in the link

 

Source: FOA (The Fiber Optic Association, Inc.)

New Products

Polatis 3000 Optical Switch
Polatis Series-3000 Optical Switch
Price excl. VAT:$0.00
Price inc. VAT:$0.00
Polatis 6000-PSS 4 Fibers Optical Protection Switch
Polatis 6000-PSS 16 Fibers Optical Protection Switch
Price excl. VAT:$0.00
Price inc. VAT:$0.00
Polatis 6000-PSS 4 Fibers Optical Protection Switch
Polatis 6000-PSS 8 Fibers Optical Protection Switch
Price excl. VAT:$0.00
Price inc. VAT:$0.00

Bestsellers

FreezeTec 12 Heating cable . Thermostat
FreezeTec 12 Heating cable . Thermostat
Price excl. VAT:$53.40
Price inc. VAT:$63.02
Yerden ısıtma için Raychem R-NRG-DM termostat
Raychem R-NRG-DM thermostat for floor heating
Price excl. VAT:$275.72
Price inc. VAT:$325.35
PERP-MELTSTICK Scratch Repair for PE Coating
PERP-MELTSTICK Scratch Repair for PE Coating
Price excl. VAT:$0.00
Price inc. VAT:$0.00

Main Brands

 Google Plus - Samm Technology  Youtube - Samm Technology  Facebook - Samm Technology  Twitter - Samm Technology  Facebook - Samm Technology
Scroll To Top